| Customization: | Available |
|---|---|
| Condensation Forms: | Water-Cooled |
| Type: | Steam Condenser |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
MKS series evaporative condenser is a kind of highefficient heat exchange equipment renovated and developed on the basis ofabsorbing the most advanced heat-exchangeTechnology abroad.
MKS series evaporative condenser uses water and air as cooling agent.The cooling agent exchanges the heat with hightemperature gaseous refnigerant agent and hence the refnigerant agent becomes liquid.Inside it has a water distribution system,condensing coils,wet deck,dehydrator and so on.Outside it has a water circulating pump,an electronic water curing device and apropeller fan on the top of condensing coil.The propeller fan strengthens the flow of the air and causes negative pressure inside.When the condenser runs,the cooling water is pumped and then sprayed by water distribution system on the surface of condensingcoil equably to form a thin layer of water film.The high-temperature steam of refrigera nt agent enters from the top of condensing coiland then the cooled liquid refrigerant agent is discharged from the bottom of the condensing coil.During this process,high temperature refrigerant agent exchanges the heat with the water and air outside the coil and increases the effect of heat exchange with thehelp of wind.After absorbing the heat of refrigerant agent,some water turns into steam and is discharged by prop eller fan.Meanwhile,the moisture in the air is collected by dehydrator to basin,and the Ungasified cooling water flows in to wet deck and its heat is takenaway by the airflow.The cooled water converges in the basin to be used circularly by the pump later.In addition,there is a ball cock inthe basin.When the water is consumed to a certain point,the ball cock will automatically open to replenish the cooling Water.
MKS series products adopt the technology ofthe combination of coil and stuffing to avoid thedry spot and dirty forming on the coils.So theperformance of heat exchange is high effective.Because of the same direction of airflow and water flow, the spray water can cover the surface of coils furthest and keeps the surface
completely wet. Compared with the reverse direction of water flow and airflow, this structure can reduces greatly the dry spot and dirty.
Single cell MKS-145~430 Boundary Dimensions and Technical Parameters
Tpye |
Heat refection under Nominal operating mode |
Propeller lan |
Water circulating pump |
NH2 Filing rate |
Weight |
|||||||||||||
Amount |
Blowing rate |
Power |
Discharge rate |
Power |
Transportation |
Operating |
||||||||||||
| KW | m/h | KW | m/h | KW | Kg | Kg | Kg | |||||||||||
| MKS-145 MKS-160 MKS-180 MKS-200 MKS-220 MKS-240 MKS-260 MKS-280 MKS-300 MKS-340 MKS-380 MKS-400 MKS-430 |
145 160 180 200 220 240 260 280 300 340 380 400 430 |
1x18000 1x22000 1x28000 1x22000 1x28000 1x35000 1x28000 1x35000 1x40000 1x35000 1x40000 1×45000 1×65000 |
0.75 1.1 1.5 1.1 1.5 2.2 1.5 2.2 3.0 2.2 3.0 4.0 4.0 |
28 28 28 28 28 28 46 46 46 46 46 46 46 |
0.75 0.75 0.75 0.75 0.75 0.75 1.1 1.1 1.1 1.1 1.1 1.1 1.1 |
17 17 17 25 25 34 34 34 39 39 39 41 |
1660 1665 1700 1860 1890 1920 2030 2045 2060 2280 2300 2330 2490 |
2685 2690 2700 2880 2870 3050 2890 3050 3060 3660 3670 3680 3830 |
||||||||||
Tpye |
Dimension | Compensate on water pipe |
Aischarge pipe |
Overflow pipe |
Air inlet pipe |
Water outle pipe |
||||||||||||
| A | B | C | D | E | F | G | H | J | ||||||||||
| mm | mm | mm | mm | mm | mm | mm | mm | mm | A | B | C | D | E | |||||
| MKS-145 MKS-160 MKS-180 MKS-200 MKS-220 MKS-240 MKS-260 MKS-280 MKS-300 MKS-340 MKS-380 MKS-400 MKS-430 |
1830 1830 1830 1830 1830 1830 1830 1830 1830 1830 1830 1830 1930 |
2210 2210 2210 2210 2210 2210 2210 2410 2410 2710 2710 2710 3010 |
1470 1470 1470 1470 1470 1470 1470 1470 1470 1470 1470 1470 1475 |
1000 000 000 1000 1000 1000 1000 1000 1000 1000 1000 1000 000 |
440 440 440 440 440 440 440 440 440 440 440 440 440 |
376 376 376 614 614 614 614 614 614 614 614 614 614 |
2000 2000 2000 1760 1760 1760 1760 1760 1760 1760 1760 1760 1760 |
2915 2915 2915 2915 2915 2915 2915 2915 2915 2915 2915 2915 2915 |
280 280 280 280 280 280 280 280 280 280 280 280 280 |
DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 DN25 |
DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 |
DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 DN65 |
DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 DN80 |
DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 DN50 |
||||
NOTES APPLICABLE ON ALL MODELS
1.The standard right hand arrangement as shown has the air inlet side onThe right when facing the refrigerant connection end.Left hand can beFumished by spevial order.Water and refrigerant connections and pumpPiping.Are always locaied on the same end of the unit
2.Standard refrigerant inlet and outlet connections are beveled for
welding And have a diameter DN100.Other connection sizcs are availableon special order.
3.Rerfrigerant charge listed is R717 operating.To determine operatingcharge for R22.Multiply charge by 1.93 and for R134A by 1.98.
4.Operating weight shown in the tables is based on total unit weight.Weight of refrigerant operating charge and basin filled to overflow level
Our products are widely applied to electricity generating stations, metallurgy, petrochemical industry,motor-dom, textile,hotels, food industry,tobacco industry, pharmaceuticals industry, electronic industry and papermaking.
The Company R&D base is located in Yixing City,Jiangsu Province,covers an area of up to30060m²,the production workshop more than 19000 square.Department of Jiangsu Province,the largest production base of the whole refrigeration products.It has a series of advancedCNC machine tool equipment to ensure product quality is excellent,the establishment of thesystem of production management standardization and quality assurance,and skilled front-line production workers,is to ensure the high quality of the products,the companyproduction equipment,large equipment,shear,punching,folding milling,car and so on 22,the annual production 350000 tons of cooling tower,a single flow from 5m³/h to 800m³/h ason 1000 kinds of specifications.
The company has a professional customer service team,providing guidance,equipmentinstallation debugging and repair and maintenance services for customers,to provide a solidguarantee for the products are applied in various industries,and won the customers trustand praise!
){kind=link}