| Customization: | Available |
|---|---|
| Condensation Forms: | Water-Cooled |
| Material: | Zinc |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
MKN series evaporative condenser is a kind of highefficient heat exchange equipment renovated and developed onthe basis of absorbing the most advanced heat-exchangeTechnology abroad.
MKN series evaporative condenser uses water and air as cooling agent.The cooling agent exchanges the heat withhigh temperature gaseous refrigerant agent and hence the refrigerant agent becomes liquid.Inside it has a waterdistribution system,condensing coils,wet deck,dehydrator and so on.Outside it has a water circulating pump,anelectronic water curing device and a propeller fan on the top of condensing coil.The propeller fan strengthens the flowof the air and causes negative pressure inside.When the condenser runs,the cooling water is pumped and thensprayed by water distribution system on the surface of condensing coil equably to form a thin layer of water film.Thehigh-temperature steam of refrigera nt agent enters from the top of condensing coil and then the cooled liquidrefrigerant agent is discharged from the bottom of the condensing coil.During this process,high temper aturerefrigerant agent exchanges the heat with the water and air outside the coil and increases the effect of heat exchangewith the help of wind.After absorbing the heat of refrigerant agent,some water turns into steam and is discharged byprop eller fan.Meanwhile,the moisture in the air is collected by dehydrator to basin,and the Ungasified cooling waterflows in to wet deck and its heat is taken away by the airflow.The cooled water converges in the basin to be usedcircularly by the pump later.In addition,there is a ball cock in the basin.When the water is consumed to a certain point,the ball cock will automatically open to replenish the cooling Water.
External dimensions and technical parameters of MKN-50-400
Type |
Propeller fan |
Weigh |
NH Filling rate |
Water circulating pump |
Dimension |
||||||||
Power |
Blowingrate |
Iransportation |
Operating |
Power |
Discherge rate |
H | U |
E |
A |
L | W |
||
| KW | L/s | Kg | Kg | Kg | KW | m'/h | mm | mm | mm | mm | mm | mm | |
| MKN-50 MKN-70 MKN-95 MKN-115 MKN-145 MKN-160 MKN-180 MKN-200 MKN-220 MKN-240 MKN-260 MKN-280 MKN-300 MKN-340 MKN-380 MKN-400 |
0.75 1.1 0.75 1.1 0.75 1.1 1.5 1.1 1.5 2.2 1.5 2.2 3.0 2.2 3.0 4.0 |
6000 9000 12000 16000 18000 22000 28000 22000 28000 35000 28000 35000 40000 35000 40000 45000 |
748 750 941 943 1162 1177 1187 1386 1409 1419 1623 1628 1643 1920 1931 1933 |
979 981 1418 1420 1639 1654 1664 1884 1907 1917 2121 2126 2141 2620 2631 2633 |
9 9 13 13 18 18 18 28 28 28 41 41 41 45 45 45 |
0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 1.1 1.1 1.1 |
34 34 34 34 34 34 34 34 34 34 46 46 46 46 46 46 |
2794 2794 2794 2794 3094 3094 3094 3094 3094 3094 3094 3094 3094 3094 3094 3094 |
1884 1884 1884 1884 2184 2184 2184 2184 2184 2184 2184 2184 2184 2184 2184 2184 |
910 910 910 910 910 910 910 910 910 910 910 910 910 910 910 910 |
374 374 374 374 604 604 604 604 604 604 604 604 604 604 604 604 |
1120 1120 1500 1500 1500 1500 1500 2000 2000 2000 2000 2000 2000 2200 2200 2200 |
1120 1120 1346 1346 1346 1346 1346 1346 1346 1346 1616 1616 1616 1880 1880 1880 |
Standard conditions:R22 and R134a has a:40.6 ºC condensation temperature,4.4 ºC suction temperature,25.6ºC wet bulb temperature.Ammonia (R717):35.7 ºC condensation temperature,6.7 ºC suction temperature,25.6 ºCwet bulb temperature.
Unit far place sink litre capacity refers to the unit and its pipeline of water required.Far left tank to ensureadequate water,make the system run time is set at the bottom of the tank water to higher than water pump inlet andfilters.(General 300mm sufficient)
Shown in the table for ammonia refrigerant filling amount,such as refrigerant R22,should be multiplied by 1.93.;
As for everything,to be multiplied by 1.98.
Note:size may vary,please do not use a diagram in the sample size for pipeline prefabrication foundation,etc.Based
on agent types and the different design environment,coil excuse number is likely to change.
Our company production base is located in Yixing,Jiangsu,coversan area of 30060m2,which produces more than more than 19thousand square meters of production plant,the Department ofJiangsu Province,a large-scale professional evaporation typeheat exchange equipment manufacturing base.
Company on the basis of the domestic and foreign advancedtechnology,development of leading products:ammonia,fluorine with two series of evaporative condenser,each seriespoints change different concurrent flow,countercurrent heat ofdozens of different types of evaporative condenser.And can bebased on the actual needs of customers,to providepersonalized customized non-standard products.There areclosed cooling tower,air cooler,brine evaporator,and othertypes of models,specifications of heat exchange products,isthe domestic production of heat exchangers for the productionof evaporative heat exchanger equipment.
Company product best-selling national 28 provinces,municipalities and autonomous regions,and exported to India.Vietnam.Taiwan,Indonesia and other Southeast Asian countriesand regions,the product is widely used in metallurgical blastfurnace and medium frequency furnace,induction furnace,chemical,petrochemical,power,textile,electronics,refrigeration,drugs manufacture,heat treatment,forgingequipment and other supporting scientific research units,hotels,shopping malls,theaters.civil building and air conditioningrefrigeration cycle cooling water back in engineering.
){kind=link}